![]() ![]() Our online repair guides can help expand your skills far beyond drills empowering you to face power tool problems whenever they arise and to fearlessly fix whatever fails you. Hopefully, this article has restored your ability to drill holes without replacing your whole drill. Reinstall the battery.Īs you just learned, fixing things yourself means more drilling with less billing. The screw is REVERSE-THREADED (requiring COUNTERCLOCKWISE rotation to secure). Secure the retaining screw with a Torx driver. (It is not necessary to strike the Allen wrench with a hammer). Use the Allen wrench to finish tightening the new chuck. Re-secure the Allen wrench in the chuck assembly. Thread the new chuck assembly onto the spindle until it is hand-tight. Remove the chuck assembly from the drill. (It may require several attempts).Ĭontinue to rotate (unscrew) the chuck assembly (by hand) until it disengages the spindle. This will (eventually) loosen the chuck assembly. While securely holding the drill against the work surface, strike the exposed end of the Allen wrench with a hammer. Position the drill on a surface that allows the chuck (and Allen wrench) to overhang the edge. Insert the short end of a large Allen wrench (as large as the chuck will accommodate) into the chuck assembly. Slide the gear selector switch to the lowest setting. Switch the transmission to the lowest setting. Remove the screw from the chuck assembly.ģ. This screw is REVERSE-THREADED (requiring CLOCKWISE rotation to loosen). Use a Torx driver (size may vary) to loosen the retaining screw. This article provides step-by-step instructions for removing and installing the keyless chuck on a DeWALT cordless hammer drill. If the drill is often used in dirty or dusty conditions, it's not uncommon for the chuck to seize-up completely (or open and close with extreme difficulty). Eventually, the chuck will need to be replaced. Each time a drill bit slips (under a high-torque situation), it will wear the chuck a small amount. The chuck could really be considered a normal-wear item on any drill. Whether you are a master carpenter or an occasional drill-seeker, provides the parts, procedures and facts you need to fearlessly fix what fails you. To find your nearest DEWALT Factory service center, Click here.Drill chuck stuck? It's time to face the fix. If for any reason you cannot remove your chuck we suggest getting your drill to your nearest Factory service center for further assistance. This will loosen the chuck so that it can be unscrewed by hand. Instructions for removing a torqued chuckġ.) Tighten the chuck around the shorter end of a hex key (not supplied) of 1/4" (6.4mm) or greater size.Ģ.) Using a soft hammer, strike key sharply in a counterclockwise direction (when viewed from the front of the tool). This will loosen the chuck so that it may be unscrewed by hand. ![]() Facing the tool strike the long end of the hex wrench sharply counter clockwise as it is a standard right hand thread. Remove screw by turning clockwise this is a left-hand screw.Ģ.) Insert the short end of a 1/4" or larger hex Allen wrench into the chuck and tighten. Insert screwdriver into the bottom of the chuck to engage screw head. Instructions for removing a keyless chuckġ.) If the unit has this screw open chuck jaws fully. Check off your home improvement tasks with. It may require several attempts to loosen the chuck Get great deals on DEWALT Cordless Drills and Drill Chucks and upgrade your power tools for your home workshop. There is no way to stop the motor from turning. Using a wooden mallet or similar object, strike the key sharply in a counter-clockwise direction. Remove screw by turning clockwise this is a left-hand screw.ģ.) With the chuck facing toward you place the key into one of the holes on the left side of the chuck. This will loosen the screw inside the chuck.Ģ.) Open chuck jaws fully. Strike the key in a clockwise direction with a wooden mallet or similar object. Most reversing drills have a left hand threaded screw located inside the bottom of the chuck.ġ.) If the unit has this screw place the chuck key, with the chuck facing toward you, into one of the holes on the right side of the chuck. To remove the chuck on your drill follow the instructions for the type of drill chuck you have: Para ver esta lista en español, por favor abra el archivo adjunto. To see this list in Spanish, please open the attachment. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |